FLASHCODE ENGIE GENERATOR
FLASHCODE ENGIE DRIVERS
FLASHCODE ENGIE CODE

The main operating components of the E4OD transmission include a torque converter clutch, six multiple-disc friction clutches, one band, one sprag one-way clutch and two roller one-way clutches that provide for the desired function of three planetary gear sets. But, itвЂ™s always a good place to start.Д¬lick here for a clean printable copy of the Jeep Check Engine Codes.The E4OD transmission is a fully automatic, electronically controlled, four-speed unit with a torque converter clutch. Diagnosing trouble codes and changing parts can still be like chasing a needle in a haystack. So, I canвЂ™t and will not promise or guarantee itвЂ™s complete accuracy. ****This information was gotten from the Chrysler FSM, Quadratec & various posts on WranglerBoard forum. This means you are done reading codes.Д¦2: EMR mileage cannot be stored in EEPROM.Д¦4: Catalytic converter efficiency failure.

FLASHCODE ENGIE GENERATOR

Also, no significant change detected in battery voltage during active test of generator output circuit.ДҐ1**: A rich air/fuel mixture has been indicated by an abnormally rich correction factor.ДҐ2**: A rich air/fuel mixture has been indicated by an abnormally rich correction factor.ДҐ5*: PCM has finished telling you the codes. (4 and 6 cyls).Д¤4*: Open or shorted condition in the engine coolant temp sensor circuit or a problem exists in the PCMs battery temp voltage circuit.Д¤6**: Battery voltage too high during charging.Д¤7**: Battery voltage sense input below target charging during engine operation. Misfire detected in one or more cylinders 1 thru 6. No movement of fuel level sender detected.Д¤3: Peak primary circuit current not achieved with maximum dwell time. Circuit shorted to voltage between PCM and fuel gauge sending unit. An open circuit between PCM and fuel gauge sending unit. An open or shorted condition detected in the fuel pump relay control circuit.

An open condition detected in the ASD relay output circuit. Auto only.Д¤1**: Alternator field control circuit open or shorted.Д¤2*: An open or shorted condition detected in the auto shutdown relay circuit. Incorrect input state detected for the Park/Neutral switch. An open or shorted condition detected in the torque converter part throttle unlock solenoid control circuit. Switch is above or below acceptable voltage.ДЈ5*: (XJs only) Cooling fan relay circuit open or shorted.ДЈ7: Relationship between engine speed and vehicle speed indicates no torque converter clutch engagement. Will not trigger a 'Check engine light'.ДЈ4*: Speed control vacuum or vent solenoid circuits open or shorted. If your Jeep doesn't have AC you will always get this code.

FLASHCODE ENGIE DRIVERS

Bad thermostat or temp sensor.Дў1**: Oxygen sensor detection neither rich or lean -or-Дў1**: Oxygen sensor input voltage stayed above normal operating range.Дў2**: Coolant temperature sensor signal above or below acceptable voltage.Дў3**: Intake air temperature sensor signal above or below acceptable voltage.Дў4**: Throttle position sensor signal above or below acceptable voltage.Дў5**: Automatic Idle Speed (AIS) motor driver circuit shorted.Дў7*: One of the Injectors output drivers does not respond properly to control signal.ДЈ3*: Air conditioning clutch relay circuit open or shorted. Will not trigger a 'Check engine light'.ДЎ3**: No change in Manifold Absolute Pressure sensor (MAP) from start to run.ДЎ4**: MAP sensor voltage too high or too low.ДЎ7*: Engine stays cold too long.

Timing belt skipped one or more teeth or intermittent loss of either camshaft position sensor or crankshaft position sensor.ДЎ2*: Battery or computer recently disconnected within the last 50 start cycles).

FLASHCODE ENGIE CODE

**= Check Engine light will illuminate during engine operation if this Trouble Code is present.Дiagnostic trouble code and descriptions:ДЎ1*: No crank reference signal detected during cranking. *= Check Engine light will not illuminate at all times if this Trouble Code it present.

Flashcode engie